
Eine Stromschienenschneidemaschine schneidet flache Kupfer- oder Aluminiumstäbe zwischen zwei Messern auf die fertige Länge. Die Schnittqualität unterscheidet eine Maschine, der eine Zeichnung anvertraut werden kann, von einer Maschine, die einen zweiten Arbeitsgang benötigt. Die beiden zu messenden Dinge sind die Rechtwinkligkeit der Schnittfläche und die Größe der Risszone am Reststück. Alles andere an der Maschine, einschließlich Kraft und Preis, ist diesen beiden Ergebnissen untergeordnet.
Was passiert im Schnitt?
Eine Schere schneidet nicht wie eine Säge. It drives a blade into the bar until the material can no longer deform plastically, at which point a crack starts at the blade edge and propagates across the section. If the blade clearance is correct for the thickness, the crack from the top edge meets the crack from the bottom edge and the face is smooth. If the clearance is too large, the cracks miss each other and the remaining material tears, leaving a rough band. Dieses Band ist die Tränenzone.
Das Spiel ist daher die wichtigste Einstellung an einer Schere und muss sich je nach Dicke und Material ändern. Eine Schere, die auf 10 mm Kupfer eingestellt ist und dann mit 6 mm Aluminium betrieben wird, erzeugt eine sichtbar schlechtere Oberfläche, obwohl an der Maschine nichts ausgefallen ist.
Methoden im Vergleich
| Verfahren | Gesicht schneiden | Geschwindigkeit | Typische Verwendung |
|---|---|---|---|
| Hydraulische Schere | Gut bis ausgezeichnet, wenn der Abstand stimmt | Schnell, ein Schlag | Produktionszuschnitt der Stromschiene vor dem Stanzen und Biegen |
| Schleifsäge | Rau, Grat an beiden Kanten, Hitzeeinflusszone | Langsam | Baustellenarbeiten, gemischtes Material, keine Schere vorhanden |
| Bandsäge | Gute Oberfläche, aber langsam und muss entgratet werden | Langsam | Dicke Abschnitte, kleine Mengen |
| CNC-Stanz- und Scherenlinie | Gute, wiederholbare, programmierbare Länge | Am schnellsten bei Lautstärke | Großserienfertigung von Platten |
Schleifmittel und Sägen sind legitime Möglichkeiten, einen Stab zu schneiden, aber sie kosten einen Entgratungsschritt und können mit einer Stanz- und Biegestation nicht mithalten. In einer Werkstatt, die bereits über eine Maschine mit drei Stationen verfügt, wird ein Schnitt außerhalb der Maschine innerhalb einer Woche zum Engpass.
What to measure on a trial cut
- Squareness: stand the cut bar on its end on a surface plate and check the gap under the face with a square and feeler gauge.
- Tear zone: measure the rough band on the offcut as a percentage of thickness. Under about 25 percent is a reasonable workshop target.
- Burr: run a finger along the top edge with a glove on. A burr that catches means the clearance or the blade condition is wrong.
- Twist: lay two cut pieces face to face and check that they close without a gap at one end.
- Repeatability: cut ten pieces and measure the length spread. A shear that holds length to plus or minus 0.5 mm is production ready.
Specification points that matter when buying
Published cutting capacity is usually given as maximum thickness at maximum width, and the two are linked. A machine rated 12 mm at 150 mm will not cut 12 mm at 250 mm. Ask for the capacity at the width you actually buy, not the headline number. Ask also about blade material and whether blades are reversible, because blade cost over five years can exceed the price difference between two machines.
The hold-down matters as much as the blade. If the clamp cannot hold the bar flat while the blade enters, the bar lifts, the clearance changes mid-cut and the face tears. Check that the hold-down force is independent of the cutting force, and that the clamp pad is wide enough for the widest bar you will run.
Maintenance that keeps the face clean
Blades wear on the corner first, and a worn corner shows up as a burr on one end of the bar only. Rotating or reversing blades on a schedule keeps the face consistent for longer than waiting for a visible failure. Check blade clearance after any change of material thickness, and clean the blade seat, because a chip under the blade tilts it and produces a taper across the width.
Häufig gestellte Fragen
Can a three station machine cut as well as a dedicated shear?
In most panel shops, yes. The cutting station on a three station machine uses the same shear principle and the same clearance logic. A dedicated shear wins on cycle time and on very thick sections, not on face quality.
Why does my cut face have a rough band at the bottom?
That is the tear zone, and it usually means the blade clearance is too large for the thickness, or the blades are worn, or the hold-down is not holding the bar flat.
Do I need a deburring step after shearing?
A light deburr is normal practice on copper because the cut edge work hardens. If the shear is set correctly the burr is small and a hand tool is enough. A heavy burr means the process is out of adjustment, not that you need a bigger deburring machine.


