• در مورد
  • |
  • تماس
  •   فارسی
به دستگاه Busbar CNC CNC خوش آمدید
  فارسی
محصولات فروخته شده در سراسر جهانتمرکز بر تامین و صادرات ماشین آلات شینه
واتساپ / تلفن:+8613853146766

پردازش گذرگاه مس در مقابل آلومینیوم: تنظیمات ماشین

زمان: 2026-11-13 مدیر: اخلاص

LTMC busbar processing machine

شینه های مسی و آلومینیومی در یک دستگاه پردازش می شوند اما با تنظیمات یکسانی انجام نمی شوند. آلومینیوم پس از رها شدن بار بیشتر به عقب برمی‌گردد، به شعاع داخلی بزرگ‌تری برای همان ضخامت نیاز دارد، و تمایل دارد بر روی ابزارهایی که به طور تمیز با مس کار می‌کنند، لکه‌دار شود. اگر هر دو ماده را اجرا می کنید، تفاوت های مهم عبارتند از: فاصله قالب، جبران برگشت فنری، آماده سازی سطح و عمر تیغه یا پانچ.

جایی که این دو ماده در واقع با هم تفاوت دارند

عاملمسآلومینیومچه چیزی را تغییر دهید
پس از تخلیه بارکوچکتربزرگترارزش جبرانی جداگانه برای هر ماده و ضخامت
حداقل شعاع داخلیمی تواند سفت تر شودبه شعاع بزرگتری نیاز داردقالب های خمشی مختلف برای مقاطع نازک
رفتار سطح در ابزارپایدارتمایل به لک و صفرا داردصورت های قالب لهستانی، روانکاری بیشتر، قالب های جداگانه
فاصله قالب برای مشت زدنسفت ترگسترده ترست های پانچ و قالب جداگانه
لبه برشکار در لبه سفت می شودنرم تر، تیغه را لکه دار می کندDifferent blade condition targets
Mass for the same currentHigherLowerHandling and support design changes

The practical consequence is that aluminum is not a drop-in substitute. A program proven on copper and copied to aluminum will produce an open bend angle, and the operator will compensate by re-running the part, which wastes time and creates scrap. Set up a separate program the first time and it behaves as predictably as copper afterwards.

Springback: the number that decides everything

When the punch releases, the bar relaxes and the free angle opens. The controller has to bend past the target angle by an amount that the material gives back. Aluminum gives back more than copper at the same thickness, and hard tempers give back more than annealed ones. That single value determines whether a batch is inside tolerance or not, and it is not transferable between materials, thicknesses or die radii.

The correct procedure is boring but reliable. Bend one trial piece, measure the free angle on a cooled bar with a digital protractor, adjust the compensation, and save the value under the material and part number. Do that once per material and per thickness, and the value stays valid until the material supplier changes.

Tooling decisions

For punching, aluminum needs a wider clearance between punch and die, because the softer material tends to pull and tear rather than shear cleanly at copper clearances. It also needs a sharper, better polished punch face, because aluminum picks up on any roughness and then scores every subsequent hole.

For bending, the risk with aluminum is cracking on the outside of a tight bend. As a rule, keep the inside radius at or above the material thickness for aluminum, and check the temper data from the supplier before accepting a drawing that asks for less. Copper tolerates a tighter radius but work hardens at the bend, so a part that is re-bent to correct an angle will be less ductile at that point.

Workshop rules that prevent most problems

  • Keep a separate compensation table per material, per thickness and per die radius, stored against the part number.
  • Keep separate die sets where surface finish is visible, or clean and polish dies between material changes.
  • Never copy a proven copper program onto aluminum without a trial bend and a measured angle.
  • Label material at the saw or shear, so a mixed batch cannot reach the bending station unlabelled.
  • Record the material supplier and heat or temper batch on the job traveler, because a supplier change can move springback.

سوالات متداول

Can I use the same dies for copper and aluminum?

For bending, often yes with different compensation and more lubrication, but expect surface marking. For punching, use separate clearance sets, because the optimum clearance differs and mixing them shortens die life on both materials.

Does aluminum need a slower bend?

Not necessarily slower, but it needs a larger radius and a validated compensation value. Speed is rarely the limiting factor; radius and springback are.

Which material is harder on tooling?

Copper work hardens at the cut edge and wears blades steadily. Aluminum smears and builds up on cutting edges, which causes poor cuts rather than gradual wear. Both shorten tool life, for different reasons.

LT Busbar Machinery Corporation (LTMC) دستگاه های پانچ، برش و خم شین CNC را تولید می کند. تجهیزات ما شینه‌های مسی و آلومینیومی را برای تولید تابلو برق، ترانسفورماتور و توزیع انرژی پردازش می‌کنند.

پیوندهای سریع

با ما تماس بگیرید

No.9566 Jingshi Rd.Jinan City ، Shandong ، چین
  [email protected]
 واتس اپ:+8613853146766
درست کردن  2025 دستگاه Busbar CNC CNC کلیه حقوق محفوظ است.