• About
  • |
  • Contact
  •   Türkçe
Welcome to CNC Copper busbar machine
  Türkçe
Products sold worldwide Focus on the supply and export of busbar machines
WhatsApp / Tel: +8613853146766

Busbar Fabrication Equipment for Switchgear Manufacturing

time: 2026-11-13 admin: Sincerity

LTMC busbar processing machine

Busbar fabrication in a switchgear plant is a sequence, and the plant runs at the speed of its slowest step. The steps are cutting to length, punching the hole pattern, bending to geometry, deburring and inspection, then kitting to the assembly cell. Most plants invest in one impressive machine and leave the other steps manual, which is why the impressive machine spends part of every day waiting.

The five steps and what each one needs

StepEquipmentWhat it decidesTypical bottleneck cause
Cut to lengthShear, or the cutting station of a 3 in 1 machineLength accuracy and cut face qualityManual handling of long bars
PunchTurret punch station or dedicated pressHole position and diameterDie changes between parts
BendBend station with angle controlAngle, leg length, flatnessSpringback correction on every part
Deburr and inspectDeburring tool, angle gauge, calipersWhether the part is accepted at assemblyNo defined inspection point
Kit and deliverRack or trolley by panel numberAssembly waiting timeParts delivered in production order, not assembly order

The fourth and fifth steps are the ones most often skipped in a capital plan, and they are the ones that generate the complaints. A part that is 0.3 mm out of square is a tolerance issue on paper and a two hour delay on the assembly floor.

Sizing each step to the bottleneck

Start from the monthly mix, not from the peak job. Count the bars per panel, the holes per bar and the bends per bar. Convert that to station hours per month, then compare with the available hours. The step that exceeds available hours is the one to invest in. In most low voltage switchgear plants the punching step dominates, because hole count per bar rises faster than bar count as panels become more complex.

A three station machine is the usual answer for a mixed low and medium volume plant, because it removes transport between three operations and it lets three operators work at once. A dedicated punch and shear line is the answer when one plant builds the same panel family in volume, because the programming and nesting gain outweighs the loss of flexibility.

Quality gates that prevent rework

  • First article inspection on every new part number: length, hole position, hole diameter, angle and leg length recorded on one sheet.
  • A defined inspection interval during a run, not only at the start, because die wear and hydraulic temperature drift both move the result.
  • Angle verification with a digital instrument, not with a square and eye, because a 1 degree error is invisible and outside tolerance.
  • Hole position checked with a pin gauge or caliper against the drawing datum, not against the previous part.
  • A reject bin at the machine, so out of tolerance parts never reach kitting.

Layout rules that save more than a machine costs

Put the shear, the punch and the bend within one operator walking distance. Every metre between stations becomes handling time multiplied by every bar in the plant. Keep the bar rack at the shear end, not in the middle, so long bars are cut before they are moved. Deliver kitted parts to assembly in panel order, because a complete kit that arrives in the wrong sequence is as useful as an incomplete one.

Frequently asked questions

What is the minimum equipment set for a small switchgear workshop?

A shear, a punch and a bender, or one three station machine that combines them, plus a deburring tool and a digital angle gauge. Anything less means buying cut and punched bars from outside, which adds lead time to every panel.

Should we buy a CNC line or a three station machine first?

If the product mix changes from panel to panel, buy the three station machine first. If eighty percent of output is one panel family, a CNC line pays back faster because programming effort is amortised over long runs.

How do we know the bending step is our bottleneck?

Measure how long a bar waits at the bend station compared with how long it is actually being bent. Waiting time above working time means the step is the constraint.

LT Busbar Machinery Corporation (LTMC) manufactures CNC busbar punching, cutting and bending machines. Our equipment processes copper and aluminium busbars for switchgear, transformer and energy distribution production.

QUICK LINKS

PRODUCT CATEGORY

CONTACT US

 No.9566 Jingshi Rd.Jinan City,Shandong,China
  [email protected]
 WhatsApp: +8613853146766
Copryright  2025 CNC Copper busbar machine All rights reserved.